features data sheet no. BRDB-1500P-1C adbd-1500p-1c mechanical specification tel.: (310) 767-1052 fax: (310) 767-7958 diotec electronics corp. gardena, ca 90248 u.s.a 18020 hobart blvd., unit b e37 15 amp silicon bridge rectifiers mechanical data maximum ratings & electrical characteristics ratings at 25 c ambient temperature unless otherwise specified. single phase, half wave, 60hz, resistive or inductive load. for capacitive loads, derate current by 20%. parameter (test conditions) maximum dc blocking voltage maximum peak recurrent reverse voltage working peak reverse voltage series number v rwm v rrm v r (rms) v rm symbol adb adb adb db db db db db db db units volts 1504p 1506p 1508p 1500p 1501p 1502p 1504p 1506p 1508p 1510p 1000 400 600 800 50 100 200 400 600 800 rms reverse voltage 280 420 560 35 70 140 280 420 700 560 controlled avalanche non-controlled avalanche ratings series: db1500p - db1510p and adb1504p - adb1508p suffix "t" indicates fast-on terminals suffix "w" indicates wire leads case: molded epoxy with integral heat sink epoxy carries a u/l flammability rating of 94v-0 terminals: round silver plated copper pins or fast-on terminals soldering: per mil-std 202 method 208 guaranteed (note 1) polarity: marked on side of case mounting position: any. through hole for #10 screw. weight: fast-on terminals - 0.7 ounces (20.0 grams) max. mounting torque = 20 in-lb. wire leads - 0.55 ounce (16.0 grams) inches millimeters min 9.6 17.5 15.7 28.4 sym bl bh d1 d2 max max 10.2 16.7 18.5 28.7 0.69 min 1.12 0.38 0.62 1.13 0.40 0.66 0.73 d3 0.53 13.5 14.5 0.57 lt 0.6 15.2 n/a n/a inches millimeters min 9.6 10.9 17.5 28.4 sym bl bh d1 ll d2 max max 10.2 18.5 11.9 28.7 0.43 min 1.12 0.38 0.69 1.13 0.40 0.73 0.47 ld 1.0 1.1 0.039 0.042 0.81 20.6 n/a n/a d3 d1 d1 bl d2 bl d1 d2 bl d1 bl + _ acac ul recognized - file #e124962 + + _ _ ac ac ac ac built-in stress relief mechanism for superior reliability and performance integrally molded heat sink provides very low thermal resistance for maximum heat dissipation void free vacuum die soldering for maximum mechanical strength and heat dissipation (solder voids: typical < 2%, max. < 10% of die area) rohs compliant i o average forward rectified current @ t = 75 c c o peak forward surge current. t = 125 j single 60hz half-sine wave superimposed on rated load (jedec method). c o amps 15 i fsm 400 t j t stg c -55 to +150 -55 to +150 junction temperature range storage temperature range r q jc v fm maximum forward voltage (per diode) at 7.5 amps dc volts volts n/an/a mimimum avalanche voltage maximum avalanche voltage v (br) min v (br) max maximum reverse current at rated v rm @ t = 25 c a o @t = 125 c a o i rm minimum insulation breakdown voltage (circuit to case) v iso typical thermal resistance, junction to case see note 1 see note 1 1.05 1 50 m a 2500 o c/w 1.2 3.01 15dbp notes: (1) these bridges exhibit the avalanche characteristic at breakdown. if your application requires a specific breakdown voltage range, please contact us. heat sink heat sink ld ll bh molded body bh lt molded body hole for#10 screw (nom. hole dia.=0.208") hole for#10 screw (nom. hole dia.=0.208")
rating & characteristic curves for series db1500p - db1510p and series adb1504p - adb1508p data sheet no. brdb-1500p-2b abdb-1500p-2b 15 amp silicon bridge rectifiers 3.01 15dbp e38 figure 1. forward current derating curve case temperature, c o average forward current, io (amperes) tel.: (310) 767-1052 fax: (310) 767-7958 diotec electronics corp. gardena, ca 90248 u.s.a 18020 hobart blvd., unit b figure 3. typical forward characteristic per diode instantaneous forward voltage (volts) instantaneous forward current (amperes) 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 1.0 10 100 1000 t = 25 c pulse width = 300 sec 1%duty cycle j o m number of cycles at 60 hz figure 2. maximum non-repetitive surge current peak forward surge current (amperes) 1 10 100 400200 300100 60 t = 125 j o c 93 0 6 12 15 18 0 50 100 150 resistive or inductive loads bridge mounted on 5 x 4 x 3" thick (12.7 x 10.2 x 7.6cm) finned al. plate 60hz 75 instantaneous reverse current, i (microamperes) figure 4. typical reverse characteristics percent of rated peak reverse voltage .01 0.1 1.0 10 100 120 140 20 40 0 60 80 t = 125 c j o t = 25 c j o
|
